noreaster.com
Forum/General Discussion/"Scratchy "Reel Noise: Pinion Bearing Replacement or Relube???

"Scratchy "Reel Noise: Pinion Bearing Replacement or Relube???

5,199 views·4 replies·by Roccus7
Roccus7
Roccus7MODnoreaster.com2019#1
Learned Colleagues:

I fish my reels "hard and put them up wet", never getting much TLC at all. I did catch hundreds of bass last year on my Go To Clash 4000 and it started making this noise the other day:


I popped the cover and slapped in some more Penn lube grease around inside, but no joy on noise abatement. There was plenty of grease in the reel when I opened it. The noise is more apparent when there's direct load on the reel, e.g. quickly reeling in a mass of seaweed, but no noise when there's no load.

It's been suggested that it's a pinion bearing problem, which fits with my observation above, and the fact that I can't get any lubrication directly on these bearings by just popping the cover. Therefore I'd like the collective knowledge here to respond to these questions before I take the reel totally apart, something I only want to do once...

  1. Is it the pinion bearings, if not what is it?

  2. If it is those bearings, should I:
    1. Clean and relubricate them?
      1. Use Penn grease or Penn Oil, if not what else?
    2. Because of my heavy usage, should I just replace the bearings?
  3. While I have the reel apart, anything else I should be looking for or should just replace as a matter of course yearly???
Thanks,
R7
Shall I go to heaven or a-fishing? - H. D. Thoreau
Veni. Vidi. Cepi. - with apologies to Gaius Julius Caesar
AdmiralOriginal Crew21,717 postsSince 2018
F
All the bearings on the Clash 4000 are sealed.Check the 2 pinion bearings and the main gear`s 2 bearings for dirt or sand/salt. After cleaning them if there is still noise they should be replaced
MateOriginal Crew74 postsSince 2019
F
Before checking the bearings remove the spool and see if the noise is present.then proceed ,The reel doesn`t look like it`s spinning freely. WD 40 to clean,followed by penn lube and oil on the bearings.
MateOriginal Crew74 postsSince 2019
Roccus7
Roccus7MODnoreaster.com2019#4
Before checking the bearings remove the spool and see if the noise is present.then proceed ,The reel doesn`t look like it`s spinning freely. WD 40 to clean,followed by penn lube and oil on the bearings.

Thanks, that wasn't my reel, something I found on YouTube that had the "correct" noise. Right now the noise has abated, but I ordered the bearings anyway so when I finally break down and take it apart, it will be "once and done".
Shall I go to heaven or a-fishing? - H. D. Thoreau
Veni. Vidi. Cepi. - with apologies to Gaius Julius Caesar
AdmiralOriginal Crew21,717 postsSince 2018
Old Mud
Old MudFREE2019#5
Thanks, that wasn't my reel, something I found on YouTube that had the "correct" noise. Right now the noise has abated, but I ordered the bearings anyway so when I finally break down and take it apart, it will be "once and done".

Call me before you order more bearings.
Tell your Children every day that you love them
I was so poor growing up, if i were not a boy i would have had Nothing to play with !! :)
All that matters in the end is that we Loved
"Life isn't about waiting for the storm to pass; it's about learning to dance in the rain."
CommodoreOriginal Crew5,182 postsSince 2018

Sign in to reply to this thread.

Thread
"Scratchy "Reel Noise: Pinion Bearing Replacement or Relube???
Sign in