noreaster.com
Forum/Inshore Tackle & Techniques/Post your 2019-2025 Fluke Pix & Trip Reports Here!

Post your 2019-2025 Fluke Pix & Trip Reports Here!

156,661 views·1393 replies·by Leprechaun·First Post·Latest
Leprechaun
LeprechaunMODnoreaster.comApr 5#1221
BTW, How many hours did you get out of the old manifolds?

Hah, good question! 10 minutes for each of the risers. One hour on the port side manifold. Not bad, considering the last four bolts have to be done by feel alone. The starboard side manifold, one hour to get out 7 of the eight bolts. The last, rear-most bolt, another hour plus.

Just can no longer contort my body enough to wedge my average-length arm back there from the front of the engine, as getting to it from the side is impossible - for me. Another example of getting too old for this, um, "stuff." I cannot image doing this for a living. Mad respect for marine mechanics everywhere - makes automotive repair look like a walk in the park.

One helpful tip is to NOT use the factory BS iron bolts that are OEM. They corrode badly, rust-freeze in the heads despite using liberal quantities of Never-Seize, making a tough job even tougher. Anyone in the know uses stainless steel "cap screws," with a good-quality 3/8" hex-drive socket - mine is Snap-on, of course! Still not a job I will ever look forward to, but these make it just a wee bit "better."

Also, always use fresh grade-8 lock washers every time the manifolds get changed - which according to universal gas inboard ritual thinking is at 6-year intervals.

One other tip - be a bit of a masochist. It kinda helps.

bolt.webp

Bolt2.webp
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
OVERBORED
Well done!
"Chance only favors the prepared mind" - Pasteur
Captain4,161 postsSince 2021
Leprechaun
LeprechaunMODnoreaster.comApr 5#1223
BTW, How many hours did you get out of the old manifolds?

Sorry, I misread your question before having my morning high-test. Yeah, well irrespective of hours run, the risers need changing out every three seasons (easy job), and both the risers and manifolds have to go at six seasons. Sitting or running the internal rust never sleeps, so the safe bet is at those intervals.

This is mandatory with a "half-closed" FW cooling system, because the cast iron mani/risers route the SW out through the exhaust pipes. This is different than a "closed" system, which includes the manifolds in the FW side of the cooling system. Most gas inboards are like mine, half-closed system.

Examples of the "full" system would be the Mercruiser Horizon series and I think some of the higher-end Crusaders. The down side of this cooling method is that the oversized engine heat exchanger must be watched like a hawk, and fully serviced or replaced when running temps move upward even a tiny bit - assuming that the RW pump has been regularly serviced as well. The H/Ex in these Full systems carries a very heavy load, considering they have to cool the engine AND the manifolds.

I think my half-system is better, but that's just my way of thinking. I'll trade-off more grunt work to eliminate possibly cooking the engine, should the H/EX clog or perforate 20 miles from the dock.

There do exist certain types of Stainless Steel riser/manifold setups - usually one piece. Locally there is a custom exhaust fabricator in Farmingdale that can build a set of SS (or copper) exhausts. My friend had a copper set on his Shammie, sister to mine w/the same PCM/Ford engine. For some reason those copper manifolds with an SS bolt-thru flanges would blow out their exhaust gasket every couple of seasons. I think it was a thermal expansion mis-match between the cast iron engine block and the SS manifold flanges, but we never did get to the bottom of that particular issue. He passed away at the age of 53 from a massive heart attack. Another of my closest friends gone forever.

Anyway, that was the $5 course in gas inboard marine exhausts. Congrads, you got an "A".
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
OVERBORED
Thanks for taking the time to explain. Any shamrocks convert to diesel?
"Chance only favors the prepared mind" - Pasteur
Captain4,161 postsSince 2021
Leprechaun
LeprechaunMODnoreaster.comApr 6#1225
My era of manufacture was available with a small-ish Perkins diesel. I've never seen or even heard of one actually being delivered. There have been a few gas to diesel conversions to Cummins 210hp diesels.

I can't see that sort of swap for reasons of cost, maintenance and the fact that such an engine will put the deck scuppers at or below waterline level. Not to mention a 26-ft boat 8-ft beam boat with a transplanted diesel will shake and vibrate excessively. Just not enough boat to absorb that much engine's drama.

Now if you just happen to have a Cummins out of a Ram pickup laying around and know how to (and can afford) to add marinization, want to replace the BW 71C with a 72C or other beefy transmission, along with a different length and diameter driveshaft and a $1500 prop, reinforce the stringers and completely redo the engine-mounting pads, have no problem modifying the cutlass bearing size in the glass/silica sand poured keel, don't mind the deck not being bailable because the scupper plugs always have to be used (except maybe underway), and KNOW that you will never see the cost come back to you should you ever sell it - well, maybe then such a swap would be for you!

Yeah, nah, from my point of view boat "hotrodding" to that extent should stay a mental exercise, not a reality. Some things should stay hypothetical. Much less drama and acceptance of eventual personal failure that way. Keep the gas, go fishing, and if you want a diesel boat, save up and buy one designed that way from the beginning . Far more peace of mind if it remains a daydream.

30 years I've owned my boat. Never once has a diesel engine made it into the top 10 (or 20) of my "upgrade wants."
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
OVERBORED
My era of manufacture was available with a small-ish Perkins diesel. I've never seen or even heard of one actually being delivered. There have been a few gas to diesel conversions to Cummins 210hp diesels.

I can't see that sort of swap for reasons of cost, maintenance and the fact that such an engine will put the deck scuppers at or below waterline level. Not to mention a 26-ft boat 8-ft beam boat with a transplanted diesel will shake and vibrate excessively. Just not enough boat to absorb that much engine's drama.

Now if you just happen to have a Cummins out of a Ram pickup laying around and know how to (and can afford) to add marinization, want to replace the BW 71C with a 72C or other beefy transmission, along with a different length and diameter driveshaft and a $1500 prop, reinforce the stringers and completely redo the engine-mounting pads, have no problem modifying the cutlass bearing size in the glass/silica sand poured keel, don't mind the deck not being bailable because the scupper plugs always have to be used (except maybe underway), and KNOW that you will never see the cost come back to you should you ever sell it - well, maybe then such a swap would be for you!

Yeah, nah, from my point of view boat "hotrodding" to that extent should stay a mental exercise, not a reality. Some things should stay hypothetical. Much less drama and acceptance of eventual personal failure that way. Keep the gas, go fishing, and if you want a diesel boat, save up and buy one designed that way from the beginning . Far more peace of mind if it remains a daydream.

30 years I've owned my boat. Never once has a diesel engine made it into the top 10 (or 20) of my "upgrade wants."
Thanks for the explanation. I know a friend owned a similar sized Sisu with a small John Deere that ran like a top. Different boat. Different specs.......Best of luck this season.
"Chance only favors the prepared mind" - Pasteur
Captain4,161 postsSince 2021
longcast
longcastFREEApr 6#1227
I had a guy in the marina that converted his Shamrock to a diesel. He worked for the marina and did all his own work. Not sure what marina he is at now.

I see him fishing once in a while
AdmiralOriginal Crew20,417 postsSince 2019
MakoMatt
MakoMattMODnoreaster.comApr 6#1228
There was a guy in the slip next to me for many years in the Tuna Club. I think he had 26’ Shamrock, with a small Perkins. I can’t remember the name of the boat, his name was Ron something……. He loved the boat and had canyon fished it back in the day.
CaptainOriginal Crew2,132 postsSince 2018
MakoMatt
MakoMattMODnoreaster.comApr 6#1229
There was a guy in the slip next to me for many years in the Tuna Club. I think he had 26’ Shamrock, with a small Perkins. I can’t remember the name of the boat, his name was Ron something……. He loved the boat and had canyon fished it back in the day.
Lep, do you remember this boat, FISH HAWK II? This is the boat I was referring to, his name was Ron, he had a slip next to mine. Don’t know if he was a member of your Shamrock Club. He passed away some years ago.
IMG_1070.webp
CaptainOriginal Crew2,132 postsSince 2018
Leprechaun
LeprechaunMODnoreaster.comApr 6#1230
No Matt, I don't recall that boat. But my memory is not what it used to be, so there's that . . .

Looks like he kept a nice clean boat.
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
MakoMatt
MakoMattMODnoreaster.comApr 6#1231
No Matt, I don't recall that boat. But my memory is not what it used to be, so there's that . . .

Looks like he kept a nice clean boat.
Pete, welcome to my world on the memory thing. 🤪
He did take good care of that boat. He also loved Fluke fishing, and was very good at it.
CaptainOriginal Crew2,132 postsSince 2018
george
georgeADMINnoreaster.comApr 7#1232
That arm has many scars on it from those manifolds!
George R. Scocca
george@nyangler.com
www.nyangler.com - Your Secret Spot Online !
CommodoreOriginal Crew5,174 postsSince 2018
Leprechaun
LeprechaunMODnoreaster.comApr 7#1233
Yes George, it sure does. 🙄
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
Avenger
Avengernoreaster.comApr 7#1234
Pete, welcome to my world on the memory thing. 🤪

Don't sweat that one. We've all known a Captain Ron or two somewhere along the line.

Mine was a wonderful guy that had a Blackfin with a pair of Isuzu diesels that he and I spent months troubleshooting. And when we finally got it working right it burned and sank at the dock. Frankly, I believe the boat committed suicide.

Still one of the finest gentlemen I ever knew.
Chrome warns this may be a phishing site. Well, Duh,... Stupid jerks can't even spell fishing right.
CaptainOriginal Crew3,431 postsSince 2019
L
Started my 2026 fluke season today . Lots of wind . Water 51 to 53 . Flood tide . Couple of shorts in the back bay . Very sluggish fish . Would only hit a light jig and gulp shrimp . Boat ran well on its first trip of the year
DeckhandOriginal Crew47 postsSince 2019
Leprechaun
LeprechaunMODnoreaster.comMay 10#1236
Huzzah!

My heavy mechanical work is now complete! It was a long, tough row to hoe, but it's behind me now.

New factory PCM manifolds and risers, new heat exchanger (Lenco Farmingdale), new starter motor (DB Electric), rebuilt the Sherwood RW pump, new Autolite plugs, factory PCM plug wires, Pertronix cap and rotor. Fresh Prestone antifreeze fill. Oil & filter change (Castrol 20W-50 with a half-pint of STP and a Wix max filter) done before the shrink-wrapping last December. Replaced some suss hoses and clamps, re-did my main bilge pump fixturing, had my office 3D print a structural truss for the engine compartment forward bulkhead and installed it with very little drama, removed any rustiness from engine and trans and gave them a fresh touch-up of black Rustoleum. This all took a ton of effort, not to mention a good bit of donated skin and blood, but it's done. Now onto my "normal" Spring prep.

A few new "tricks" I've added this time around. First, it's really tough to get at the 4 rear-most bolts of each manifold and those 4 rear spark plugs too, for that matter. At 70 years old now, not only can I no longer contort my body sufficiently to reach back there whilst laying atop the engine, but it seems like my arms got shorter too. I don't know if that's medically possible, but it is what it is. So, I took out the big stainless motor mount lag bolts and put a "cheapie" Harbor Freight 8-ton hydraulic bottle jack under the motor mount, each side in turn. OMG, why did it take me 30 years of ownership to remedy this nightmare? Dense, I guess.

IMG_7526.webp

This made all the difference, that's for sure. Just had to make certain that the "down-load" on the inside of hull was well distributed with 1x6 board. Each mount (there are 4, including the trans mounts) carries about 300lbs of weight, so gotta be a little careful with this plan of action. Didn't hear any cracking, so good to go.

Instead of doing the aforementioned near impossible "by blind feel" method, I could now use a simple 3/8" inch x 12" extension, swivel and hex-driver from the side of the deck to R&R those torture-inducing rear-most manifold stainless cap screws. This was huge!

IMG_7530.webp

And here's the most important (and least expensive) "tool" for this type of work, which I figured out half-way thru the job -

gloves.webp

That's right, just a cheap pair of cotton work gloves, with the fingers cut off. Again, OMG, what a difference! No more deep scratches on the backs of my hands from wire tie cut-offs and assorted other nasties. Hey, dropping an American V-8 into a boat with an 8-foot beam has some truly great advantages. The other side of the coin is that access to bolts, hose clamps, etc, is at shall we say, a "premium." the glove solution made it MUCH more comfortable to reach down, in, and around all the pain inducing hand-snaggers.

And now she sits, ready to fire. That will happen some time this coming week, as today my wife graciously allowed me to use up "her" day's morning to complete this work.

Fingers crossed.

IMG_7552.webp
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
MakoMatt
MakoMattMODnoreaster.comMay 10#1237
Huzzah!

My heavy mechanical work is now complete! It was a long, tough row to hoe, but it's behind me now.

New factory PCM manifolds and risers, new heat exchanger (Lenco Farmingdale), new starter motor (DB Electric), rebuilt the Sherwood RW pump, new Autolite plugs, factory PCM plug wires, Pertronix cap and rotor. Fresh Prestone antifreeze fill. Oil & filter change (Castrol 20W-50 with a half-pint of STP and a Wix max filter) done before the shrink-wrapping last December. Replaced some suss hoses and clamps, re-did my main bilge pump fixturing, had my office 3D print a structural truss for the engine compartment forward bulkhead, removed any rustiness from engine and trans and gave them a fresh touch-up of black Rustoleum. This all took a ton of effort, not to mention a good bit of donated skin and blood, but it's done. Now onto my "normal" Spring prep.

A few new "tricks" I've added this time around. First, it's really tough to get at the 4 rear-most bolts of each manifold and those 4 rear spark plugs too, for that matter. At 70 years old now, not only can I no longer contort my body sufficiently to reach back there whilst laying atop the engine, but it seems like my arms got shorter too. I don't know if that's medically possible, but it is what it is. So, I took out the big stainless motor mount lag bolts and put a "cheapie" Harbor Freight 8-ton hydraulic bottle jack under the motor mount, each side in turn. OMG, why did it take me 30 years of ownership to remedy this nightmare? Dense, I guess.

View attachment 115317

This made all the difference, that's for sure. Just had to make sure that the "down-load" on the inside of hull was well distributed with 1x6 board. Each mount (there are 4, including the trans mounts) carries about 300lbs of weight, so gotta be a little careful with this plan of action. Didn't hear any cracking, so good to go.

Instead of doing the aforementioned near impossible "by blind feel" method, I could now use a simple 12" 3/8" extension, swivel and hex-driver from the side of the deck to R&R those torture-inducing rear-most manifold stainless cap screws. This was huge!

View attachment 115320

And here's the most important (and least expensive) "tool" for this type of work, which I figured out half-way thru the job -

View attachment 115318

That's right, just a cheap pair of cotton work gloves, with the fingers cut off. Again, OMG, what a difference! No more deep scratches on the backs of my hands from wire tie cut-offs and assorted other nasties. Hey, dropping an American V-8 into a boat with an 8-foot beam has some truly great advantages. The other side of the coin is that access to bolts, hose clamps, etc, is at shall we say, a "premium." the glove solution made it MUCH more comfortable to reach down, in, and around all the pain inducing hand-snaggers.

And now she sits, ready to fire. That will happen some time this coming week, as today my wife graciously allowed me to use up "her" day's morning to complete this work.

Fingers crossed.

View attachment 115319
You da’ man Pete!!! I think I got you by a year or two so FYI it ain’t get any easier, but I’m sure you know that. May you be rewarded for all your efforts with another double digit!!
CaptainOriginal Crew2,132 postsSince 2018
H
holtyFREEMay 10#1238
Good work, Pete! I remember those days when I owned the Mackinaw. Not an easy job.
regards Holty
MateOriginal Crew107 postsSince 2018
Leprechaun
LeprechaunMODnoreaster.comJun 6#1239
Had to work through some setbacks but floating now!

Been super-busy with work and all sorts of boat-related issues. Turns out that after I completely finished buttoning up the engine work and tried to start her, yeah, HOLY CRAP!, gas shooting 18" straight up out of the carburetor. And as soon as I got off the key a small carb fire erupted, which luckily I had taken off my sweatshirt and used that to snuff it out. It never ends.

Only one way that an engine behaves this way - she was spinning in the wrong direction, and so became a gas pump instead of a gas vacuum. Let me explain - boat engines are available in two rotations, left-hand and right hand - or to put it another way, clockwise and counter-clockwise. This is because twin inboard installations (and I guess outboards too) use a pair of engines with opposite rotations, so to cancel out prop steer from the two engines turning in the same direction.

I have what is called a "standard rotation" engine, meaning when you view the pulleys at the front of the engine when running they turn clockwise, a.k.a., left-handed. they sent me a right-handed starter, but it arrived in a left-handed box. After my blood pressure calmed down I confirmed this was the case by tapping the key and seeing the pulleys move CCW. Oh, for the love of . . . The idiots (who shall remain nameless) sent me the right starter BOX, with the wrong starter in it.

I'm so effing DONE with the incompetence in just about about everything I deal with - work or "play," always an issue. Two and a half days of hard work down the drain. I had to burn two MORE days of valuable vacation time to re-jack up the motor, re-remove the starboard side manifold/riser combination, dump the fresh antifreeze (I was able to save most of it), re-take the heat exchanger out (a nasty job btw, because the four hoses' clamps are VERY difficult to access), and swap out the starter for the correct one. Then reinstalled all the above. Two + days I'll never get back. She runs fine now, so at least there's that. No thanks to a certain major marine supplier, that's for sure.


<video><source></source></video>

God, I'll never get tired of listening to a big gas V-8's rumble.

Anyway, once that all got done (for the second time), I was able to pull the shrink off her and get going on the "normal" Spring commissioning work.

IMG_7578_edited.webp

Here she sits this morning, boat stands removed, with Chris HippyChic Hauling on the way to get her off my lawn and over to the Freeport ramp.

And an uneventful shake-down run to my slip at Yachtsmen's Cove marina. Tomorrow I do a bit more cleaning and then the hunt for Mr. Mat begins thereafter.

IMG_5833_edited.webp


Oh and LET'S GO KNICKS! My "other" favorite team!
"Luck" is when preparation meets opportunity.
I prefer fishing evolution to fishing extinction.
If ya want to clean up the water, ya gotta get the pigs out of the creek.
CaptainOriginal Crew2,216 postsSince 2018
BoatGuy
BoatGuynoreaster.comJun 6#1240
You picked a good time to get it running. My son-in-law went fishing a caught 50 fluke on a friends boat.
(They didn't say where and I don't ask) 2 keepers. The water was 63 degrees.
First MateOriginal Crew780 postsSince 2019

Sign in to reply to this thread.

Thread
Post your 2019-2025 Fluke Pix & Trip Reports Here!
Sign in